Infrared (IR) Remote Control Repeater Kit (TAA Compliant)
#40430
C2G
Infrared (IR) Remote Control Repeater Kit (TAA Compliant) is rated
out of
5 by
30.
Bazaarvoice SAP Hybris Integration Version 2.8.1
$81.99 $123.99 MSRP USD
Does your entertainment system have wooden doors, or would you like to mount your components in a closet? Without a clear line of sight infrared (IR) signals from a remote control will not reach the equipment. We have the answer. Our remote control repeater kit contains all equipment necessary to remotely operate 4 components (expandable to 12 components) using your standard remotes. Mount the IR receiver in a central location and connect to the IR distribution block. This block repeats the signals through emitters to your electronic components. Your components may now be mounted in your entertainment center, closet or another room! The kit is self-contained and easy to connect.
With this kit, you may mount a receiver in a convenient place on or near your entertainment system. The receiver has a 9 foot cable that is then attached to the repeater system that is mounted in your entertainment cabinet. The kit includes 4 emitters. These emitters are connected from the repeater system and placed over the IR receiver of the equipment.
The IR receiver and IR repeater have blinking blue LEDs to confirm receipt of the IR signal; the IR repeater is designed for mounting on shelf or wall. You can use your existing remotes for simple installation and hookups. Packaged for resale.
For your convenience, the AC/DC Adapter (#98025) is available for this item. To order this replacement part, please call us at 1-800-506-9607.
Please Note: Careful consideration must be used when placing the IR receiver near a plasma display. Since a plasma display emits IR frequencies during use, it may cause interference. At this time, the ATT U-Verse cable boxes are not compatible with the C2G, formerly Cables To Go, IR Receiver Kit. The product team at C2G is working hard to find a solution for this issue and will update you as soon as possible. Replacement components may be ordered online: 10ft Infrared Receiver with 3.5mm Plug (#98045), 10ft Single Infrared Emitter Cable (#40432) and 10ft Dual Infrared Emitter Cable (#40433).
With this kit, you may mount a receiver in a convenient place on or near your entertainment system. The receiver has a 9 foot cable that is then attached to the repeater system that is mounted in your entertainment cabinet. The kit includes 4 emitters. These emitters are connected from the repeater system and placed over the IR receiver of the equipment.
The IR receiver and IR repeater have blinking blue LEDs to confirm receipt of the IR signal; the IR repeater is designed for mounting on shelf or wall. You can use your existing remotes for simple installation and hookups. Packaged for resale.
For your convenience, the AC/DC Adapter (#98025) is available for this item. To order this replacement part, please call us at 1-800-506-9607.
Please Note: Careful consideration must be used when placing the IR receiver near a plasma display. Since a plasma display emits IR frequencies during use, it may cause interference. At this time, the ATT U-Verse cable boxes are not compatible with the C2G, formerly Cables To Go, IR Receiver Kit. The product team at C2G is working hard to find a solution for this issue and will update you as soon as possible. Replacement components may be ordered online: 10ft Infrared Receiver with 3.5mm Plug (#98045), 10ft Single Infrared Emitter Cable (#40432) and 10ft Dual Infrared Emitter Cable (#40433).
Quantity
270 In Stock
-
Added to Favorites Go to favoritesRemove from favorites?Something went wrong. Please try again later.
- Send
- Save as PDF
Features
- Allows for control of devices behind closed doors
- Includes emitters to control up to four devices
- LED light confirms IR communication
WARNING: Cancer and Reproductive Harm www.P65Warnings.ca.gov
Specifications
General Info
| Color | Black | ||
| Type | Accessory, Active Device, Kit | ||
| Application Sector | Commercial, Residential | ||
| Product Line | C2G | ||
| Country Of Origin | Taiwan, Province Of China | ||
| Features | IR (Infrared) | ||
| Included | AC/DC Adapter, IR Emitters, Mini IR Receiver | ||
| Warranty Type | 5-Year | ||
| UPC Number | 757120404309 |
Dimensions
| Product Height US | 0.98 in | ||
| Cable Length | 9 ft | ||
| Product Length US | 1.93 in | ||
| Product Width US | 2.93 in |
Trade Programs
| TAA Compliant | Yes |
Technical Information
| Has Battery | No |
Resources
Reviews
Rated 3 out of
5
by
Steve the Tinkerer from
Works as advertised...sort of
I bought this for use in a large storage unit with a loft. I have a second set of speakers up there and wanted a way to control volume from the receiver downstairs (under the loft). Packaging, simplicity and, despite others' comments, to the point instructions, seemed to meet my needs...until I hooked it up the way I intended - power to the switched outlet on my receiver. The box was powered but the repeater appeared not to be accepting a signal - as evidenced by the lack of the blinking blue light. Double checked. and it was hooked up correctly. Figured I would box it up and return but decided to plug in to a wall outlet and it worked as advertised - nothing more, and slightly less.
Date published: 2011-12-17
Rated 5 out of
5
by
Highland Doc from
Good unit
Just some unpublished info for all; As with most of these type devices, you can parallel connect 2 of the receivers and then control your home stereo/theatre system from two different rooms.
Date published: 2011-04-14
Rated 5 out of
5
by
Ramblin Ron from
Excellent Choice
This product was perfect for my situation. I hung my 52" LCD on the wall but didn't want any other equipment to show. I hid the Satelite box and Blue-Ray DVD in an adjoining closet behind the wall. I'm sitting about 25 feet from the TV and everything works just perfectly.
Date published: 2012-07-12
Rated 5 out of
5
by
Steve from
OK - here's the deal with this.
It must be DIRECT wired to the Infrared Remote Control Repeater base unit. This wall plate takes the place of the mini IR receiver that is included with the base unit. You will need to run a cable from the back side of this plate to the base unit. An Ethernet cable works fine as the connection instructions call for two twisted pair to be used. Installed as intended, it works flawlessly.
Date published: 2012-06-11
Rated 3 out of
5
by
Tech home user from
Not quite there
purchased to control my uverse cable box to a flat screen tv on a bedroom wall.
cable box was in closet and wired thru wall to tv. ir receiver was passed thru wall
using a 1/8" stereo plug and then a plug to plug cable to ir box.
found best operation by using the 2 emitters attached to uverse.
Sometimes requires multiple trys to change a channel. Controller to tv
for on off or volume works without a hitch every time. Just ir to uverse
box via repeater is inconsistent
Date published: 2012-03-07
Rated 4 out of
5
by
Woodbike from
Took persistence to get it to work!
System includes a Sony Blue-ray, Motorola Satellite receiver and a Harmon Kardon AVR210
System worked with the Satellite box immediately, but I could not get the Harmon Kardon receiver to work with the supplied emitter.
I called tech support and they did not have any recommendations.
Based on a tip on a website, I tried plugging directly into the IR in on the HK with a cable I use to plug my iPhone into my car stereo.
Now I have the whole system working!
Date published: 2011-04-02
Rated 5 out of
5
by
Bubba from
works great
This was used in a commercial setting for a lunchroom TV. The cable box was hidden above the T-Bar ceiling and only the TV is visiable on the wall. System works perfectly.
Date published: 2013-09-03
Rated 5 out of
5
by
George from
Works Great
I mounted my plasma on the wall in the family room and moved all my A/V equipment into the basement below it. The 40430 extends the remote to the basement with minimal lag time. A/V Receiver, DVD Player and Cable Box (FIOS QIP 6416) all work well. I have the IR receiver under a bookcase so the remote control range is reduced but I am sure this would not be true if the receiver was out in the open.
Date published: 2010-01-12
Bazaarvoice SAP Hybris Integration Version 2.8.1
Questions & Answers
is model 40430 compatible with TWC cable box from CISCO (Explorer 8642)
Yes, the IR repeater kit does work with that cable box.
Date published: 2017-10-06
I installed the IR Remote Control Repeater kit and it works fine. Although there is no blinking blue confirmation LED on either the receiver or the control unit. Is there a way to switch the blue LED on and off?
Unforutnately there is no way to turn off the Blue Light. This is a confirmation light letting the user know that the device is receiving a IR signal.
Date published: 2017-10-05
I'm planning on using a logitech remote to trigger the IR to an onkyo receiver, benq projector, sony blue ray player and a verizon fios motorola cable box. I'm looking to run this with a cat5e cable (approximately 50 ft of cable). Will this work? Can y...
I'm planning on using a logitech remote to trigger the IR to an onkyo receiver, benq projector, sony blue ray player and a verizon fios motorola cable box. I'm looking to run this with a cat5e cable (approximately 50 ft of cable). Will this work? Can you also please provide me with the cable color specs for proper installation.
Yes this will work at 50ft. There is not a particular color that you will have to use to connect this device.
Date published: 2017-10-05
I have to make a longer run and would like to do it over Cat5 cable as it is all ready in place. Can you please tell me the color codes for the 3 wires (ie: power, ground & IR signal)?
The signal is white, ground is red and +12V is black.
Date published: 2017-10-05
I would like the wiring layout of the plug.
The plug is signal (tip), ground (ring), 12V (sleeve).
Date published: 2017-10-06
I'm a little slow, so bear with me. The specs say Frequency Range - 34 to 60 KHz, which makes it sound like it will work on any frequency within that range. On the other hand, it also says dual band, which makes it sound like it will only work at 34 an...
I'm a little slow, so bear with me. The specs say Frequency Range - 34 to 60 KHz, which makes it sound like it will work on any frequency within that range. On the other hand, it also says dual band, which makes it sound like it will only work at 34 and 60. I need it for a cisco 9865 cable dvr box which requires 57khz, is this compatible? Thanks Mark
This should not have a issue with the Cisco DVR. The fequency range that is given covers almost every IR remote frequency.
Date published: 2025-03-06
Hi there! Just bought this IR Repeater. I need to know what is the wire scheme (color based) to connect the receiver cable to the hub, once i need cut it... Thank you very much...
The device works best when the plug is not removed. Here is the color pin, Black is 12V Red is Ground and Signal is White.
Date published: 2017-10-05
Will this work with a Motorola VIP1200 set-top box? I've tried placing the repeater all over the front of the VIP1200 without success.
One of our techs is working with you through email.
Date published: 2017-10-05
Does the IR remote extender work with Bell FIBE TV boxes in Canada? Model # VIP 2202. Thanks
To date there have been no reports of any compatibility issues between your device and the IR Repeater Kit. If you experience any issues we are more than willing to help solve them.
Date published: 2017-10-05
Is this a single or dual band repeater? I.e. does it work for higher frequency devices ? Thank you, Aster
The IR receiver can handle a dual band frequency 34 - 60kHz.
Date published: 2017-10-05
How can I extend the length of the receiver? Will a standard stereo cable work?
Yes, a standard 3.5mm stereo audio extension cable will work when needing to extend the length of the receiver. We recommend a maximum of 25 feet for this application.
Date published: 2017-10-05
I own this unit and the IR Emitter is no longer sending my Comcast remote commands to the Comcast HD box (the signal to the HDTV however works fine). The failure started when I was moving around the cabinet and the top of the IR Emitter that sticks to ...
I own this unit and the IR Emitter is no longer sending my Comcast remote commands to the Comcast HD box (the signal to the HDTV however works fine). The failure started when I was moving around the cabinet and the top of the IR Emitter that sticks to the front of the Comcast HD box came off and the end wire became exposed. Please advise if/how I can replace the faulty IR Emitter & get it working again.
You can try to experiment with different placement of the emitter to see if the Comcast HD box will receive the IR signals in a different area. If not you may want to consider replacing the emitter cable. You can consider emitter replacement part 40432 (http://www.cablestogo.com/product/40432).
Date published: 2017-10-05
Does this repeater kit work with Direct TV receivers?
Yes, it works with DirectTV receivers.
Date published: 2017-10-05
I would like to plug the wall adaptor in the switched receptacle of my receiver. But if I plug the other end in the status plug the repeater doesn't work ,the green led lights up but no blue led with the remote. Do I need 2, 12 volts source?
You can still connect this to the reciever you would just need to connect the power adapter to the 12v.
Date published: 2017-10-05
Are the components, specifically the AC adapter, UL approved and meet US safety standards for electric devices?
The AC/DC adapter is the only component in this kit that is UL listed. Product 40430 is considered a low voltage device with minimal current draw.
Date published: 2017-10-05
Can you tell me correct way to extend the ir receiver eye with cat 5 cable. Thank you
If you are extending it via Cat5e, you have a couple of options. You could purchase our 37036 keystone adapter and connect 3 wires, ground, +12V, signal. The status port does not need to be connected. See pinout between the block and the 3.5mm keystone below: IR block - 3.5mm keystone +12V - G GND - R Signal - L
Date published: 2017-10-06
Will this work with my camcorder Canon Vixia HV40
I was unable to locate what frequency range the Canon Vixia HV40 operates in. Our 40430 Infrared Repeater Kit receives Infrared in a 34 kHz-40kHz frequency range and transmits in a 38 kHz frequency range. Contact Canon to see if their camcorder operates in this range. If so, then it will work with our Infrared Repeater Kit.
Date published: 2017-10-05
looking to make sure that this repeater is compatible with newer equipment: denon avr1913 receiver, samsung UN55ES6100 LED tv, comcast cable box, Panasonic DMP-BDT220 blu ray player, and the harmony 650 universal remote. Thanks!
The only known incompatibilities would be the AT&T U-Verse box and Marantz receiver. Your equipment should not have any issues with our IR repeater kit. If you do experience any problems, please contact us back and we will help you resolve them.
Date published: 2017-10-05
Will this product work for a range of 75 feet? All of my components are in the lowere level
The receiver will extend to 125ft using 37036 and Cat5e cable. Please check product uses on this page for more information.
Date published: 2017-10-05
This looks like a great product that gets great reviews. I just have two questions. First, do you know if this is compatible with Yamaha receivers, specifically the RX-V673? Also, how does the signal get transmitted to the receiver? Will I be placing a...
This looks like a great product that gets great reviews. I just have two questions. First, do you know if this is compatible with Yamaha receivers, specifically the RX-V673? Also, how does the signal get transmitted to the receiver? Will I be placing an emitter over the IR receiver eye on the receiver or just putting an emitter in the cabinet with the components to be controlled? Thanks!
We have been unable to determine the infrared frequency your Yamaha receiver's range, however, our 40430 transmits the infrared signal at a frequency of 38 kHz. You will want to confirm with Yamaha if their equipment can receive a signal in that range. The IR signal is transmitted from your remote to our receiver which travels to the receiver box and is relayed to the emitters near your equipment. You would want to place the emitters either on the IR window of your Yamaha receiver or a few inches away (inside of your cabinet) for best results.
Date published: 2017-10-05
I'm looking for an IR extender that is compatible with a Cisco Explorer 4640HDC set-top box which operates at 57 kHz. The cablebox manual notes that Cisco part # 1004648 can be plugged directly into the 3.5mm IR port on the back of the cablebox and pow...
I'm looking for an IR extender that is compatible with a Cisco Explorer 4640HDC set-top box which operates at 57 kHz. The cablebox manual notes that Cisco part # 1004648 can be plugged directly into the 3.5mm IR port on the back of the cablebox and power is supplied via the stereo plug. Is your Dual Band IR Receiver (part # 98045) a suitable replacement for the Cisco receiver (i.e., can it be plugged directly into the IR port of the cablebox without the need for a connecting block)?
Unfortunately this part is only compatible with our part number 40430. This can not be used as a direct connection with any cable box.
Date published: 2017-10-05
Will this item work with the Remote Control Repeater Kit (Product #: 40430)? If yes, how can I hook it up?
Yes, it will work with 40430. You would use a cable with at least 4 conductors like a Cat5e or Cat6 cable and connect the screw down terminal block on the distribution hub from 40430 to the connection block on the back of the wall plate. Both will have terminals for +12V, GND, Signal, Status.
Date published: 2017-10-05
I would like to connect this to my pc. there is a connector block for signal and status. do you have info for the usage of this block?
Unfortunately, we do not have this information for connecting it to a PC.
Date published: 2017-10-05
I want to locate the IR receiver of a C2G 40430 approximately 25 feet from the AV equip. Can I extend the existing cable w/ a standard stereo extension cable? If the answer is, "don't know, have to try it," is there a max distance you think would work?
You can use a regular 3.5mm stereo audio extension cable up to 25ft. Over that length we would recommend using Cat5e wire from the screw down terminal on the distribution block.
Date published: 2017-10-06
is cat 5 needed or can I use 4 conductor phone wire
Cat5 is suggested but you can use a 3 conductor wire.
Date published: 2017-10-05
Is this receiver PLASMA TV PROOF, or will the plasma TV interfere with it's reception.
The receiver is not plasma proof. A plasma TV could interfere with the IR receivers reception.
Date published: 2017-10-06
Will this work with the UVerse Motoroal VIP-2200 series?
No. We have product 40696 that will work with AT&T Uverse
Date published: 2017-10-06
Does this work with AT&T Uverse cable box?
No. We have product 40696 that will work with AT&T Uverse
Date published: 2017-10-06
Can I add a second signal receiver with a splitter and do you sell the signal receiver?
Yes, you can use a 3.5mm stereo audio splitter cable and use an additional IR receiver (#98045).
Date published: 2017-10-05
The remote from My Onkyo TX-NR414 receiver makes the LED on the ir receiver and the block flash. The onkyo turns on and off with remote in same area but not with the repeater. Any trouble shooting tips.
Make sure you move the repeater around to try different positioning. The LED should flash blue when recieving signal. If you are still having issues, please contact support.
Date published: 2019-02-25
Bazaarvoice SAP Hybris Integration Version 2.8.1